Winkelwagentje

Winkelwagen is nog leeg.

Winkelwagen is nog leeg.
Op voorraad

Akasa Slimfan | PWM Case Fan | 80mm PC Fan | 4-pin Cooling Fan | 80 x 80 x 10.8 mm | Black | Suitable for HTPC and Slim System | AK-FN076

5,99€ 12,74€
Gratis verzending bij bestellingen boven 25,99€

Productdetails

  • Smalle ventilator met een diepte van slechts 10,8 mm, ontworpen voor HTPC's of compacte systemen in kleine ruimtes.
  • PWM-snelheidsregeling zorgt voor een nauwkeuriger afvoerluchtvolume, de snelheid varieert van 600-3000 tpm.
  • Verbinding via 4-pins stekker.
  • Nauwkeurig uitgebalanceerde messen met lage luchtweerstand.
  • Gebruiksvriendelijk ontwerp maakt de montage snel, eenvoudig en efficiënt.


Productbeschrijving


Akasa Slimventilator, 80 x 80 x 10,8 mm

Geschikt voor HTCP en Slim-systemen: Smalle ventilator, slechts 10,8 mm diepte, ontworpen voor HTCP of compacte systemen in kleine ruimtes. PWM-functie: Intelligente PWM-snelheidsregeling zorgt voor efficiënte koeling bij hoge en lage belasting. Verbinding door middel van 4-pins stekker. PWM snelheidsregeling garandeert nauwkeurigere hoeveelheden afvoerlucht, snelheid van 600-3000 tpm. Nauwkeurig uitgebalanceerde messen met lage luchtweerstand. Eenvoudige installatie: Gebruiksvriendelijk ontwerp maakt de montage snel, eenvoudig en efficiënt.

PWM behuizingsventilator

 80 mm pc-ventilator

4-pins ventilator

Specificaties:

Afmetingen: 80 x 80 x 10,8 mm
lagers Enter Lager
Snelheid 600-3000 tpm
Maximale luchtstroom 26,53 CFM
Max Static Air Pressure 1,81 mm-H²O
Geluidsniveau: 27,09 dB(A)
Nominale spanning: 12 V
Connector PWM-4pin
Productcode: AK-FN076

Onivaldo
7 augustus 2025
Produto veio lacrado na Caixa.Mas o intenso barulho é muito ruim.Descartei o seu uso.
ナウシカ
22 juli 2025
小型なので高回転でうるさいかと思ってましたがケース純正のフロントFANがうるさい為全然気にならないです8センチ薄型はこれしか選択肢ありませんがとても良いファンだと思いました
Matthew Vaerewyck
23 juni 2025
Unbeatable for the price. Capable of running at high rpms and bound to fit in any sff case where space is limited for fans. Highly recommended!
M. Elek
27 februari 2025
I built a low-profile PC using older parts. It's assembled in a slim case that requires a low-profile CPU cooler.The stock CPU cooler fan sat far too high, so I was looking for a thin fan. I originally dropped in a 60mm fan, but it wasn't nearly enough - it ramped up to max speed every five minutes or so. This 80mm fan works much better. It's low noise, and being PWM runs faster only when needed. Because it moves more air, it doesn't have to work as hard. Very pleased with this.I attached it to the heat sink with four dots of silicone (Shoe Glue). I've done this before. Using four dots holds the fan in place but allows you to easily pry it loose.
Matteo Scarsini
26 december 2024
Je l'ai utilisé pour une mod de mon Thinkcentre Tiny, a la place du ventilateur blower d'origine. Les 4 broches permettent le câblage correcte e le control actif par la carte mere