Andonstar Digitale microscoop met 1080p display en HDMI-microfoon voor ADSM302 reparatiegereedschap voor printplaten

Ho comprato questo modello convinto che fosse più che altro un giocattolino visto il costo relativamente basso, ho provato altri microscopi solo usb ma la resa delle immagini era a dir poco pessima, con questo ADSM302 appena tolto dalla scatola si ha invece una buona impressione, bello solido, struttura in metallo, scorrimento liscio senza giochi o inceppamenti, già mi scappa un piccolo sorriso, collego tutto, lo accendo ed è li che rimango a bocca aperta, il piccolo monitor incorporato da 5pollici si vede non bene ma benissimo, nonostante sia piccolo le immgini si vedono belle definite molto meglio rispetto ad altri microsocpi collegati al pc con schermo più grande, così ho collegato l'uscita hdmi al mio monitor ed è li che mi è proprio caduta la mascella, una sola parola, perfetto!!! Si vede una bomba anche ingrandendo al massimo si vede sempre bene ma già all'ingrandimento dalla foto allegata è perfetto per poter operare su componenti piccoli senza difficoltà... mano tremante a parte :D Se proprio devo trovare non dico un difetto ma una mancanza era meglio avere la base di un qualche materiale gommoso e non in metallo così da avere un piano meno scivoloso e mettere due batterie nella confezione per il telecomando.... Ultima considerazione, come si vede in foto si riesce ad avere un ingrandimento perfetto tenendo l'ottica lontano dall'oggetto, questo per chi lo utilizza per riparazioni con il saldatore è un vantaggio non indifferente così da avere spazio per manovrare.

De media kon niet worden geladen.

Todo funciona según lo esperado, había leído muy buenas críticas y no me ha defraudado. La pantalla está bien pero conectado a un monitor por HDMI se sale. En internet tienes Mods para montarlo en un soporte de micrófono o ponerle un anillos de leds alrededor de la lente.

最初に8インチの商品を購入しましたが、不良「充電器なし、液晶内蔵電池不良」で返品しました。再度アマゾンでほかの商品を探してみましたら、こちらの商品にHDMI機能とレンズフィルター付きですので、こちらの商品にしました。タブレットPC修理作業をやっていますので、外部モニターでPCBAを確認できると非常に見やすいです。また、レンズフィルターも付いていますので、レンズの掃除は楽です。欠点は日本語に設定しても、再起動したらデフォルトの英語に戻ります。全体的にいいと思います。

I don't often do this but I thought this deserved a write up now I've used this properly over the last few months..I'm an electronics engineer and needed a replacement microscope for doing SMD rework and inspection in my home lab, but didn't want to spend a fortune, but at the same time wanted something good quality and fit for purpose..I saw a review on youtube, where some guy had several different microscopes all set up in a row, looking at the same reference object and this one REALLY stood out from the group, Noticeably clearer image, nice and bright with optics that allowed for plenty of room under the lens to actually do some work whilst viewing what your doing.... and it wasn't the most expensive either..Despite being sceptical having been burned before, bearing in mind scopes for the purpose I need normally cost several thousand £'s, I took the plunge but expected it to be fairly inadequate and cheap and nasty like other hobby type scopes I've used in the past..Conclusion: This is a really good scope for the money, highly recommended for anyone doing close up work to a professional level..PRO's:Very clear image, good magnification range, accurate and easy focusing, very large working range underneath (can be around ~150-200mm,away depending on what your looking at), Good build quality feels really robust and solid.CON'S:Built in screen goes off when plugging in a HDMI cable (not a big deal in practice, but I do use the built in screen when soldering AND then a super sized image on a 22in HDMI monitor to check my work, so I have to plug and unplug the HDMI to do this). LED light swan-necks could do with being stiffer as they tend to slowly wander away from where you put them sometimes, Unit comes on automatically when you switch the power on (I know that sounds a strange negative, but mine is constantly plugged into a 'bench supply' which comes on with a master switch, then I turn on/off whatever equipment I might be using at the time, the power plug is buried deep amongst dozens of other plugs, so each time I power the bench,on the scope also switches on even when I might not want to use it, so I have to manually turn it off each time I work on my bench or pull the power connectors on the back , a mild inconvenience but also annoying, why not just default it to off when plugged in??,...Granted, it's NOT in the league of a professional microscope, but for the money it's very highly recommended for hobbyists of any level and as a general purpose jobber scope for professionals...... I'm going to be buying a couple of them, one for the van for mobile work and one for the kids for fun.