Aquor House Hydrant V1+ vorstvrije wandkraan buitenkraan met snelkoppeling en anti-sifon, vriesbestendige spoelslang, 2 inch, leisteen grijs

I am extremely happy with our Aquor House Hydrant V1+! It's outstanding and I couldn't find anything like it on the market. It's evidently built from high quality materials that will last. We live in the UK with a brick house on a pedestrianised street so we didn't want a typical outdoor tap. This one is very discreet and noone will know what it is. I'd highly recommend it! The only thing I will mention is that when we hired a plumber, it took them longer than anticipated to install it as it is a unique outdoor tap. Also, it didn't seem to work with an additional dual-check valve which the plumber ended up removing (so I'd mention this to your plumber to speed-up troubleshooting). However, this is not an issue as there is built-in backflow prevention within this unit/the hose attachments. Finally, I'd recommend buying the plastic Hozelock "threaded tap connector" size 26.5mm / 3/4", as the metal one did not fit the hose attachment.

This item was really easy to install yourself and easy to use. Works great. For your install make sure you don't buy one that is too long. If you follow what I'm saying the install is easy. If you don't follow and make the same mistakes i dud it could be more of a pain in the .....This is hoe I di it in case you want to know.Measure from the spigot base to the first bend of your pipe. (If your pipe is straight from the spigot and stays straight for a number of feet then thats even better get the longest one) if not the measurement doesnt have to be very accurate. You just have to make sure you buy one that will go though the wall and os shorter then your pipe before it bends. (of course you can put it in no matter what but for easy easy easy this is the way)This was the first mistake that I made. If you are ordering the 6 inch one it's actually 8 inches long. Add 2 inches in over all length to the item and then add about an inch and a half for your shark Bite ( which I'll get to) so this means if you measure the length from your outside spigot base to the first bend in your pipe, Say it is 10 inches then you want to order the 6 inch one. To be safe add 4 inches to the length for proper fitThis is exactly what I did and it was easy. My pipe was 10 so I got the 6 inch one.1 Shut off the water.2 Unscrew spigot3 Get a pipe cutter and cut pipe as close to the outside wall as close as you can. ( you may have to use a hacksaw)4 widen hole in the wall because typically the aquar was wider than ither spigots i had ) widen hole of needed using a drill and hole saw5 put your sharkbite onto the aquar with pipe tape and tighten. ( if you don't know about these sharkbites you can get them any home improvement store like lowes , home depot they snap into your pipe and you dont need to solder (sodder) a pipe or use clamping tools. If you look at my pictures you will see what one looks like)6 Put the aquarium spigot in the hole and see what length it is to your pipe. Mark your pipe where the end of the sharkbite is ( the sharkbite goes in less than a quarter-inch so give yourself a but extra. And then cut ( use liquid paper or any marker you can see on a pipe.)7 cut your pipe again, remember you can't add but always take away.8 put aquar and the sharkbite , that you already put together into the hole and click your pipe in. ( you will literally hear a click. )8 screw the aquar to your wall on the out side and you are done. Don't forget the plastic cover and angling piece they give you so your aquarium drains properly.I've done three of these so far and I can do it less than a half hour now. This thing is made great and looks and operates fantastic. Already multiple friends have bought and used them . Everyone loves them and there is nothing to say about them that isn't good

Love this hose connector. Is easier to install than I thought and very nice to use. Good work

We are soon to complete a major extension to our home. Yesterday the plumber arrived to start all of his work. He’s now installed four Aquors around the extension perimeter. Two have been installed “paired” as “hot” and “cold” for my wife’s outdoor gardening nook. Two are mounted on the faces of concrete, faux stone facades. The plumber first saw these a few months ago when he was scoping his work. Today, I learned he’d already purchased some for his own property, he was so impressed with the functional design. His company is now talking with their distributor to encourage them to stock them. To say they’ve been a hit is an understatement. To a homeowner, they are as revolutionary as the microwave oven and the automatic ice maker. They will change how we use water outside forever. Thank you Aquor!!

So far so good. Just installed, nice fit and finish.No more ugly spigot . Highly recommend.I Will be buying more for all around my house.