Winkelwagen is nog leeg.
Winkelwagen is nog leeg.Productbeschrijving
Specificatie: Staat: gloednieuw Artikeltype: batterijcontroleapparaat 1. Spanning: Meetbereik: 0-200 V Minimale resolutie: 0,01 V Startspanning: 0,05 V Meetnauwkeurigheid: 1%2. Stroom: meetbereik: 0-300A3. Prestaties: meetbereik: 0-60000 W Minimale resolutie: 0,01 W Startvermogen: 0,2 W Meetnauwkeurigheid: 1%4. Impedantie: meetbereik: 0-1000 Ω Minimale resolutie: 0,1Ω5. Interne weerstand: meetbereik: 0-999 mΩ resolutie: 1 mΩ Meetnauwkeurigheid: 1%6. Capaciteit: meetbereik: 0-1000AHMinimale resolutie: 1mAH Meetnauwkeurigheid: 1%7. Resterende batterij: display: de resterende batterijcapaciteit wordt weergegeven door het batterijsymbool, in totaal 10 roosters, waarbij elk rooster 10% van de stroom vertegenwoordigt.De resterende batterijcapaciteit wordt berekend op basis van de huidige batterijspanningswaarde. 8. Energieverbruik: meetbereik: 0-9999 KWh, overloop op nulminimale resolutie: 1 WhMeetnauwkeurigheid: 1%9. Looptijd: bereik: 0-999 uur (geen belasting wordt niet geteld)Formaat: 0: 00: 00-999: 59 (overloop naar nul)10. Stroomverbruik: normale werkstatus: 0,03-1,2 W slaaptoestand: 0,5 mW-0,5 WHet stroomverbruik is afhankelijk van de waarde van de testspanning. Hoe hoger de spanning, hoe hoger het stroomverbruik.11. Bedrijfstemperatuur: -20 °C - + 60 °C Pakketlijst: 1 x tester, 1 x shunt, 1 x Chinese en Engelse handleiding, 1 kabelset
Federico
4 juni 2025
De media kon niet worden geladen.
Sonja Winckler
22 mei 2025
Leider ist die Bedienungsanleitung grottenschlecht und nicht zu gebrauchen. Dadurch habe ich keine Kontrolle über die Kapazität der Batterie.
HD
30 maart 2025
I bought this to monitor my boats leisure battery set up and consumption as i have installed a new fridge and want to keep an eye on the battery drain when the engines are not on. I have 4x120AH batteries linked so the output is 24V.Cables:The supplied cables are so short just put them in the bin - To the supplier = Please give at the very lease 0.5m length cables.I dug out some thin multi core cable to use as a replacement. You will need very thin 4 core cable.Physical Installation:The physical installation is very simple. Just make sure your put the shunt on the negative side between the negative battery side and the negative busbar. I located mine just after the isolator switch and before the busbar so it would only be on when the electrics were turned 'on'.Instructions:I find it is always a gamble when buying a Chinese electronic product from Amazon due to the set up instructions being hard to work out. Most often someone has worked it out and with a bit of research, often in these reviews or on YouTube it is possible to find some simple instructions that work. I haven't been able to for this product thus far.Once wired in it reads the voltage and amp draw ok. The concern I have is that I wasn't able to set it up with the battery capacity so I don't think the battery percentage indicator can be correct. I don't think it analysis this on its own. If anyone is reading this and has worked it out I would appreciate it if you could comment back!A good point is that you can turn off the display, so its not blinding at night :)I have only given this product 3 stars as the cables could be longer and I am not convinced that the product automatically sets up to the battery bank AH capacity and I don't seem able to set this up myself. IF I do I will update my rating.
Giraud
8 november 2024
Controle de charge et décharge set batterie solaire!
Aanbevolen producten
Misschien vind je dit ook leuk
Aanbieding
52,99€
111,48€