BIGTREETECH SKR Mini E3 V3.0 voor Ender 3 Silent Mainboard Upgrade 3D Printer 32 bit Control Board TMC2209 Stepper Motor Driver voor Ender 3 v2 Ender 3 Pro Ender 5 CR10

Echt een upgrade voor mijn printer alle mogelijkheden om alles intestellen en 10 keer zo stil

Goed product , alles compleet en netjes ingepakt.Alleen geen documentatie meegeleverd wat resulteerde in wat extra zoekwerk.

Bestelling geplaatst op Amazon. Bij het artikel stond volgende dag in huis. Echter na 3 dagen een bericht dat de verzending was vertraagd. Vervolgens enkele dagen later nogmaals een bericht met dit keer dat de zending kwijt was. Geld zal worden terugestort binnen enkele dagen... Toch maar even een andere aanbieder zoeken die zijn eigen spullen niet kwijtraakt.

er is nog geen configuration.h voor ender 5.ender 3 is geen probleem.

heerlijk rustig geworden dan mijn vorige bordsteppen moter zijn geruisloosmooi kleuren led scherm allemaal veel duidelijker een upgrade van waarde

Werkt perfect en ook de juiste maat. Heb nog niet alle opties kunnen bekijken door een verlate zending van Amazon maar tot op heden werkt mijn ender 3 pro beter dan ooit tevoren

You will probably have to buy a JST-XH contact to connect the hotend fan, I don't know if this is supposed to be sent or not. I also didn't get the micro USB cable, but I managed to find a way around.

Drop in replacement su ender 3 pro.Scheda che da il meglio di sé con firmware klipper, apprezzo molto la presenza di tante porte aggiuntive e i pin dedicati per l’interfaccia spi con raspberry pi eliminando la necessità del cavo usb.Comprata in offerta a meno di 50€, se la vostra scheda necessita di sostituzione è una bell’upgrade, anche se a mio modo di vedere non necessario vista la stampante in questione.

Mein Creality v4.2.2 Board hat ein Problem mit dem E-Stepper. Ich wollte es durch ein v4.2.7 ersetzen. In den Rezensionen dazu hatte ich von Qualitätsproblemen gelesen und mich - entsprechend einer der dortigen Empfehlungen - zu BTT umentschieden.Im Nachhinein eine ausgezeichnete Entscheidung. Das BTT passt perfekt und mit den TMC2209 läuft der Drucker jetzt super leise. Die Verarbeitung ist erstklassig - kein Vergleich zu meinem v4.2.2, das erhebliche Qualitätsmängel aufweist (beim/nach dem Ausbau gesehen).Falls ich nochmal ein Board kaufen müsste - auf jeden Fall wieder BTT.Da es in den Rezensionen negative Aussagen wegen bereits geöffneter Verpackungen gibt.Meine Verpackung war ebenfalls "geöffnet", ABER:* der Karton enthält keine Spur von einem Kebestreifen/Klebepad etc. - möglicherweise klebt BTT einfach nicht zu* die antistatische Folientüte - in der das Board war - zeigt keine Spur von Aufschneiden/Aufreißen, die Einkerbungen zum Aufreißen sind noch da - möglicherweise schweißt BTT die einfach nicht zu* Ich gehe also davon aus, das mein Board keine Retourenware war!Ein paar Tipps zur Installation und Firmware:* Anschluss der Lüfter - hier musste ich einmal umstecken, weil "Part Cooling" und "Enclosure Fan" in manchen Beschreibungen vertauscht sind* die von BTT bereitgestellte Firmware mit BL-Touch Unterstützung hat den selben nicht erkannt -> da kein Z-Endstop Schalter angeschlossen war hat sich die Nozzle beim Homing ins Bett gebohrt* sofort funktioniert hat hingegen die Firmware von "Seelenkind" (Seelenkind/BIGTREETECH-SKR-mini-E3 auf GitHub)* letzendlich habe ich mir die Marlin-Firmware dann selber gebaut (geht ganz einfach), um noch ein paar mehr Parameter meinen Wünschen anzupassenMein Setup:* Ender-3 Pro* CR-Touch* Direct-Extruder (UniTak3D Ender 3 Direct Drive Upgrade-Kit mit Redrex Dual Gear Extruder)

I used this to replace the dead 8-bit board of my old Prusa clone (HicTop 12)Note: You need to really know what you are doing, and have to be comfortable to crimp and solder your own cables if not using this for an Ender!Was overall very easy for me to install in my Prusa clone.The new drivers are amazing! Compared to the super old drivers from the old 8 Bit board these are virtually noiseless. I can actually sit in the same room and work when the printer is printing.Overall very positively surprised that the swap out went so smoothly.I cannot say anything about the MOSFET quality as I am using two separate big ones for bed and hot-end use. So no experiences using the on-board ones. Tip: Use separate big MOSFETs, they come cheap (2 pack for way below $30) and usually ready to use, with cable clamps etc., they reduce any heating issues, reduce fire issues and take any heat/power strain off the board. Bought mine on Amazon years ago, never regretted it.Pros:1. Very compact design, in fact it is truly "mini"2. Excellent drivers, make a noisy printer virtually silent, cooler included3. Marlin 2.0 shines on this board4. Works exceptionally well with my Orion Piezo auto leveller, I now get the bed perfectly levelled with 9-point in less than a minute. Every print's first layer is now pure art5. Board build quality and online documentation ranges from very good to absolutely sufficient for such a competitively priced board.6. Noticeably better performance with this 32-bit board.7. Super easy to flash the firmware updates8. Lots of people own this and there is quite a lot to google out there if you ever get stuck. Did not have to use their customer service once.Cons:1. You should really be comfortable with configuring Marlin, soldering, cable crimping, etc. if you do not do a direct Ender board update but use this for a different printer. Because you will have to make at least some new cables and connectors.2. Patience is necessary, as a move to a new board is never trivial, lots of fun (?) testing is necessary3. Had to buy the Color TFT E3 V 2.0 from BT as well, as my old screen would just not work with the board, but, to be honest, totally worth the investment, as the TFT not only is a touch-screen but a very powerful mini Octoprint as well, among other things it has a rather useable terminal built-in. No more running back and forth between the computer with Octoprint and the printer.

I recently upgraded my Ender 3 with the BIGTREETECH SKR Mini E3, and it has completely transformed my printing experience. This board is a drop-in replacement for the stock Creality board, making installation super easy. It fit perfectly, and with the pre-installed firmware, I was up and running in no time.The biggest improvement is the silent stepper drivers—my printer is now whisper-quiet compared to the stock board. No more loud motor noise, just smooth, precise movements. Print quality has also improved, with noticeably fewer artifacts and better control over retractions.Another great feature is the 32-bit processing power. Compared to the stock 8-bit board, everything runs smoother, from faster calculations to better handling of complex prints. It also supports Marlin 2.0, giving me access to advanced features like linear advance and thermal runaway protection for added safety.For anyone looking to upgrade their Ender 3 (or similar printers) with a silent, powerful, and reliable mainboard, the SKR Mini E3 is an absolute must-have. Highly recommended