Winkelwagentje

Winkelwagen is nog leeg.

Winkelwagen is nog leeg.
Op voorraad

DollaTek 5 stuks Dual Driver L298N PWM Speed DC motor driver board dual H-bridge stappenmotor module

3,99€ 7,99€
Gratis verzending bij bestellingen boven 25,99€

Productdetails

  • De dubbele H-bridge motordriver kan twee gelijkstroommotoren of 4-draads steppermotoren aansturen
  • Geïntegreerde TSD, zonder je zorgen te hoeven maken over de motoruitval
  • Ultra-klein formaat, geschikt voor montage en auto
  • De motoraandrijfmodule is ideaal voor gebruik in intelligente auto's, auto's en robots op batterijen.
  • Voedingsspanning 2 V ~ 10 V, kan twee gelijkstroommotoren of een 4-draads bi-fase stappenmotor regelen, kan de voorwaartse rotatie of omgekeerde rotatie bereiken, je kunt het toerental instellen. Elk kan 1,5 A gelijkstroom leveren, piekstroom tot 2,5 A, warmtebescherming en kan automatisch worden hersteld.


Productbeschrijving

Producteigenschappen:
Stap 1: Het gebruik van geïmporteerde originele chips, ingebouwde lage weerstand MOS-schakelaar, minimale hitte, geen koellichaam, klein formaat, laag stroomverbruik, ideaal voor batterijvoeding.
Interne transistorschakelaar L298N, laag rendement, hoge koorts, noodzaak om koellichaam toe te voegen, omvangrijk, L298N zeer gemakkelijk te verbranden.
Stap 2: Dual 1,5 A x 2, piekstroom van 2,5 A, geïntegreerde thermische beveiligingsschakeling, geen angst dat de motorvergrendeling verbrand is, automatisch herstel na het vallen van de temperatuur.
Stap 3: Klein formaat, licht van gewicht, 0 standby-stroom, is de ideale keuze voor je automodel.
Productgegevens:
Stap 1: de H-dubbele brugmotor kan twee gelijkstroommotoren of een 4-draads bi-fase stappenmotor aansturen;
Stap 2: de voedingsspanning van de module 2V-10V;
Stap 3: Signaalingangsspanning 1,8-7 V;
Stap 4: Enkele bedrijfsstroom 1,5 A, piekstroom tot 2,5 A, lage stand-by stroom (minder dan 0,1 uA);
Stap 5: Ingebouwde gemeenschappelijke geleidercirkel, wanneer de ingangspin zwevend wordt gelaten, werkt de motor niet correct;
Stap 6: geïntegreerde warmtebeveiligingsschakeling met hysterese-effecten (TSD), zonder je zorgen te hoeven maken over de motoruitval.
Stap 7: Productafmetingen: 24,7 x 21 x 5 mm (lengte, breedte, hoogte), zeer klein formaat.
Waarschuwingen:
Stap 1: Omgekeerde positieve en negatieve prestaties zullen zeker schade aan het circuit veroorzaken.
Stap 2: de uitgang is kortgesloten tot massa of kortsluiting bij de uitgang en de motor geblokkeerd, de chip zorgt voor warmtebescherming, maar bij spanning dicht bij of meer dan 10 V en de piekstroom is groter dan 2,5 A, kan de situatie ook brandwonden veroorzaken.
Inhoud levering:
5 x gelijkstroommodrivermodule


Pankaj Jadhav
21 juni 2025
Finally was able to work with it when header pins were soldered. It is working as expected and pretty simple to use
S. Stroud
1 juni 2025
I needed a driver to control a 12V solenoid from an Arduino. This looked ideal as it apparently has an L298N driver IC which is well able to operate with my 12V supply.However it turns out that the chip fitted is actually an MX1508, which only takes up to 10V and is therefore totally unsuitable. Returning.
Tomas Raulino Galvão
19 mei 2025
Work as intended
Mauro Fabio Sulfaro
15 mei 2025
Gia testato e funziona come da aspettativa
Girolamo Daniele Bruneo
8 mei 2025
Ho preso questo modulo perchè integrare un L298N classico (con i terminali screw) in una PCB risultava complicato.Sono rimasto molto soddisfatto dal suo funzionamento, ma attenzione che non si tratta di un modulo con L298N ma di un MX1508. Il che va bene (anche meglio dell'L298N, avendo un minor voltage drop) se si pilotano motori fino a 10V.
Tony S
18 november 2024
I've bought several of these motor driver boards to use in a self-balancing robot project. I was interested to see if I could common up the outputs to in effect double the drive current to a single motor, and found that you can, provided that you also common up the inputs, IN1+IN3 and IN2+IN4. The other thing I discovered was that the truth table found on other sites implies that you need to apply PWM to one or the other inputs to reverse the motor direction; there by needing two PWM signals. This is not the case, you can get away with only one PWM signal and a direction logic signal; provided when you change direction you also reverse the mark/space of the PWM in your code. The MX1616 device is a Chinese chip which I couldn't get any information on, so I have only given it 4 stars because of that. I've also not tested the device to the limit, so I can't vouch for whether or not the claims for current handling are valid. I'll find out more when I build and test my robot.