Winkelwagentje

Winkelwagen is nog leeg.

Winkelwagen is nog leeg.
Op voorraad

DollaTek PCM2704 USB DAC USB Power Fiber Optic Coaxiale Analoge Output sz-11 Pi Raspbian Rasp BMC

5,99€ 10,99€
Gratis verzending bij bestellingen boven 25,99€

Productdetails

  • Ondersteuning 16 bit kHz / 44,1 kHz / 48 kHz
  • Spanning: 5 V (USB-interface)
  • Signaal-ruisafstand: 98 dB; dynamisch bereik: 98 dB
  • Distortie: THD + N: 0,006% (RL> 10 k); Distortie: THD + N: 0,025% (RL = 32)
  • USB-ondersteuningssysteem: WinXP / voor Windows 7 / Doe voor Mac OS 9 / OS X, Android 4.1 Systeemmodel (moet OTG ondersteunen)


Productbeschrijving

Hoofdchip hifi-niveau PCM2704 USB-decoderchip, de prestaties zijn beter dan het onderste uiteinde van de populairste chip CM102S-serie op de markt, maakt gebruik van USB-voeding, uitgang kan direct op de headset worden aangesloten, maar ook pre-digitale uitgang voor geavanceerde DAC-decoder levert digitale SPDIF-signalen een betere geluidskwaliteit. omdat het gaat om een externe geluidskaart om het chassis te vermijden ernstige elektromagnetische storingen, de signaalruisverhouding en de geluidskwaliteit kunnen worden verbeterd.
PCM2704 is een monolithische digitaal-analoge converterchip. Het beschikt over twee digitaal-analoge converter-uitgangskanalen en een geïntegreerde USB-interfacebesturing. Interface voldoet aan USB1.1-standaard. PCM2704 kan 48 kHz, 44 kHz en 32 kHz bemonsteringssnelheid, 16-bits stereo of mono-audiogegevensintegratiesoftware binnen de chip het volume en de mute-functie kunnen worden gesynchroniseerd om het volume in te stellen en de computer te ontvangen. Stroomvoorziening via USB, analoge uitgang rechtstreeks in de computer op de USB-poort aangesloten, hoeft niet te worden verbonden.
Technische gegevens:
Ondersteuning 16-bits kHz / 44,1 kHz / 48 kHz
Ondersteuning 2-kanaals analoge uitgang, S/PDIF-uitgang.
Dynamic Range / Signaal-ruisverhouding: 98 dB.
THD + N = 0,006%.
Een USB-interface 1.0 specificaties
Win XP / Win 7 / Win 2000 gratis rit.
Win 98SE moet de schijf installeren
Formaat: 55x50 mm
Specificatie van PCM2704:
Spanning: 5 V (USB-interface),
Vervorming: THD + N: 0,006% (RL> 10 K)
Vervorming: THD + N: 0,025% (RL = 32).
Signaal-ruisafstand: 98 dB.
Dynamisch bereik: 98 dB.
Uitgangsvermogen hoofdtelefoon: 12 mW (RL = 32).
Inhoud levering:
1 x PCM2704 USB Power Soundkaart decodering deck


JimmyAK
9 juni 2025
If like me you are frustrated by a lack of optical output on the PS5, then this is a cheap and simple solution. After a bit of research I discovered that not all USB DACs will work with the PS5 as it doesn't support the latest UAC2 standard, being limited to the older UAC1 protocol. So for instance, my Fiio K3 DAC isn't recognised by the PS5. So I went looking for an alternative and found this. Although it's marketed for the Raspberry Pi, it works perfectly with the PS5. As a bonus it also incorporates a headphone output. All this for less than a tenner (although you'll need to factor in a USB A > USB B cable if you haven't already got one). I paired it with a 3D printed case that I downloaded from thingiverse (see picture) and now have optical audio from my PS5!
Customer
1 juni 2025
For my uses, getting optical audio from todays gaming consoles it works great, no complaints.
Davide
25 maart 2025
Viene visto subito e si gestisce senza problemi!
Martin Pagan
17 maart 2025
Kupiłem to ustrojstwo, żeby wyprowadzić dźwięk z PS5 i Switcha na wzmacniacz i kolumny i nie grać ciągle w słuchawkach. Konsole normalnie wykrywają je jako zewnętrzną kartę dźwiękową, ale nie wiem, czy mój egzemplarz jest wadliwy czy zachodzi jakiś brak kompatybilności, bo w przypadku połączenia kablem optycznym do Marantza PM7005 z głośników kilka razy w 1-2 minutowych odstępach dochodzi cichy trzask, który potem zanika. Nie jest to problem z kablem ani wzmacniaczem, bo po podłączeniu go do karty dźwiękowej komputera ten problem nie występuje. Po podłączeniu kabla optycznego do Gustarda X16 trzaski nie występują, ale za to na Switchu brakowało dźwięków interfejsu, a trzaski nie ustępowały, jak miało to miejsce w przypadku PS5.Wyjścia coax nie testowałem, bo nie mam odpowiedniego przewodu.
Simon Bach
10 november 2024
Habe ihn für einen Rasperry Pi benutzt, um diesen an meinen AV Receiver via Toslink anzuschließen. Damit sind Brummschleifen und Störungen vom Rasperry geschichte und der Sound ist top. Streame mit dem RPi Spotify und meine Medienbibliothek. Einrichtung und Benutzung ohne Probleme, habe ihm noch ein extra Gehäuse aus dem 3d Drucker spendiert, damit das Ding auch ordentlich geschützt im Hifi Regal seinen Dienst tuen kann.