Winkelwagentje

Winkelwagen is nog leeg.

Winkelwagen is nog leeg.
Op voorraad

E-Z LOK 400-M8 Inzetstukken met schroefdraad voor hout, Installatie Kit, Messing, Inclusief M8-1.25 Mes Draad Inserts (5), Boor, Installatie Tool

15,99€ 34,15€
Gratis verzending bij bestellingen boven 25,99€

1.Maat:M8-1.25 Knife Thread Inserts (5)


Productdetails

  • THROND INSERT INSTALLATIE KIT - E-Z LOK Installation Kit maakt het gemakkelijk om machinedraden in hard hout te plaatsen.
  • EIGENSCHAPPELIJK MES DRIDE — E-Z Mes draad inserts bieden superieure houdkracht met behulp van een eigen externe "mes" draad om in het hout te snijden.
  • Messing of staal opties: messing schroefdraad inserts of roestvrijstalen schroefdraad inserts beschikbaar. Roestvrij staal wordt aanbevolen voor bijzonder hard hout en overal corrosiebestendigheid nodig is.
  • VOOR GEBRUIK MET TOEPASSINGEN: De E-Z Mes schroefdraad inserts voor hout zijn ontworpen voor gebruik in hard hout zoals eiken, kers en esdoorn.
  • SET INCLUSIEF: Handige kit bevat schroefdraadinzetstukken voor hout, boor en schroefdraadinzet installatie aandrijfgereedschap.


Productbeschrijving

E-Z LOK Draad Installatiekit Voor Hout

E-Z LOK Schroefdraadmontagekit voor hard hout. Deze handige kit bevat inzetstukken met schroefdraad, een boor en een installatie-aandrijving.

Deze draadinzetstukken voor hardhout zijn ideaal voor toepassingen waar strippen of draaderosie mogelijk is. Perfect voor meubels, scheidingswanden, vitrines, verzendcontainers, overal waar een bevestiger in hout wordt gebruikt. E-Z Messengaren bieden superieure houdkracht met behulp van een eigen externe "mes" draad om in het hout te snijden. Ze zijn ontworpen voor gebruik in hard hout zoals eiken, kers en esdoorn. Interne draadmaten variërend van #4 tot 3/8 en M3 tot M10 zijn verkrijgbaar in messing of roestvrij staal. Roestvrij staal wordt aanbevolen voor bijzonder hard hout en overal corrosiebestendigheid nodig is.


Matthew
27 mei 2025
The threaded inserts are phenomenal, however, the installation tool is complete garbage. Save your money, use a good bolt and hardware instead. Both my m6 and m10 install tool snapped off after the insert was too deep to remove. Talk about a headache.
ken richter
22 april 2025
I used this tool to repair an expensive bedframe. The knife-edged inserts easily cut into a hardwood (mango). The drill size is an awkward size (33/64) - the system could have been designed for a readily available bit (e.g. 32/64). Ken
Joshua Price
2 april 2025
No matter how I try to use the install tool it seizes up. I have put it in by hand slowly and backed it off every 3 rotations to make sure the tool will unthread without pulling out the insert...but by the time it is flush to wood surface it is seized. I have tried lubricating the tool thread, still seizes. Absolutely trash and almost ruined my project. Also ship your stuff without stickers over the minimal labels, and include some instructions if this is a common problem.
Customer
28 maart 2025
The driver included in this kit was the wrong size (too large) and would not fit into the threaded insert opening. This required me to take the kit components to a hardware store. I purchased and EZ LOK driver of the correct size and was able to proceed with my project. The drill and inserts were ok.Very disappointed with the kit purchase and I'm sure there are more customers that will experience the same issue. EZ LOK should be anxious to recall this kit
Jason
13 november 2024
The diameter of the tool was too large to fit the inserts. The inserts were correct leading me to believe the wrong tool was included. Had to return. Unless without the correct tool.