GLOBAL CACHE iTach IP2IR Ethernet naar IR adapter

I purchased this so I can build my own KVM solution to switch USB and HDMI inputs via 2 blasters connected to this box.However, be warned, you will need to be tech savvy or a programmer to use this. I coded my client using golang.You "record" the IR using their provided "iLearn" software... which gives you a string of characters.You then connect via your (own) app on TCP port 4998 and then send down the command (which starts with sendir)The unit does not store these IR codes.. you send them each and every time to port 4998 on the unit.It was hard to find this information from their docs! Took me ages to figure out.. hence the 4 stars. 1 star dropped for lack docs.

Das Gerät arbeitet in meinem Wohnzimmer störungsfrei.Die in der Lieferung enthaltenen Emitter kann man angeblich über Y-Kabel an einem Port anschließen.Ich persöhnlich nutze nur einen Emitter, alle anderen Geräte (6Stück) kann ich mit dem IR-Blaster abdecken. Den Blaster wollte ich zuerst mit einer 5m-Klinkenverlängerung betreiben, dabei verliert man aber anscheinend zuviel Sendeleistung. Ich habe dann festgestellt das es viel einfacher geht und den Blaster unten am Phono/TV-Schrank festgeschraubt. Das erste Gerät steht direkt über dem IR-Blaster, das letzte hängt auf ca. 2m Höhe.Wie gesagt arbeitet das Gerät bei mir Störungsfrei mit der Software IRule für Android(zusätzliche Kosten ab ca. 40Euro).Ein kleiner Nachteil ist das bei der Programmierung von Makros relativ große Wartezeiten zwischen dem Wechsel von Geräten eingefügt werden müssen (0,5-1s).Das kann jedoch an der Nutzung des Blasters liegen.Der größte Nachteil ist jedoch der hohe Preis.Trotzdem volle Punktzahl auf Grund der einwandfreien Funktion (Ist in diesem Bereich anscheinend nicht selbstverständlich).

I do not believe the average home consumer purchases this type of device, so I'm writing this for the semi educated consumer that understands what they are buying or trying to achieve.This device acts as a "bridge" between two commonly used protocols: TCP and Infrared. Global Cache is one of the leaders in these types of devices, used by many home automation companies to integrate home automation controllers with receivers, TVs, and just about every type of device that has a remote control and takes infrared commands.Centralized home automation is not just for the uber-rich or the professional installer anymore. A Do it Yourself (DIY) community of people are out there that have built many great tools for building your own home automation solution. With the communization of devices like an iPad, you can use software to design your own remote control. These types of devices are critical to controlling devices in your house.RS232 is substantially better at delivering commands to a device than infrared, but many times you have no choice. In that case, this is the best device for bridging that gap to include infrared devices in your home automaton scheme. Keep in mind that infrared cannot give you feedback (such as acknowledgement that the device received the command, or the ability to ask a device a question - What is the currently volume level?) where RS232 and TCP do. So, if you want to communicate with a device via a home network, RS232 or TCP are preferred.These devices work great with a home automation package called Indigo by Perceptive Automation, and can be integrated using a plugin called Global Cache. Certainly these devices can be used with just about any home automation system, but these are two of the best for the DIY market. Feel free to reach to me if you have questions.

This is an awesome little device. The single IR blaster included works quite well. The two adhesive emitters were easy to set up and worked fine with a 25 foot 2.5mm stereo extension cable, to control a projector on/off.The IR learner was hard to use at first. Just put the iTach and the remote control on a flat surface, point the remote's emitter at the back of the iTach with about 2 inches distance between the two. There's a pinhole reset button that apparently also includes the recessed IR receiver. You may need to angle the remote, so it's IR emitter has a "line of sight" directly into this little hole on the back of the iTach.I get frequent crashes with the iLearn software if I use any of the functions except learning a code, trimming it, and saving it. Reconnecting the iTach (it apparently times out after a while), clearing windows, etc, caused the program to eventually crash. Other than that the iLearn and iConvert tools work perfectly.I tried both OpenRemote and iRule, and settled with iRule because I couldn't figure out how to get repeating IR codes to work smoothly with OpenRemote for my Motorola set-top-box. iRule occasionally goes into a mode where it fails to send commands to the iTach, but I think this mostly has to do with my Nook Tablet's groady wireless. Otherwise iRule and the iTach work together perfectly, including the extensive IR device library available with iRule.If using OpenRemote, assign the iTach a static IP _before_ programming a bunch of commands to save yourself a lot of grief when your DHCP server decides to play musical chairs.

The IP2IR hardware works well. What they don't tell you is that, other than for testing, it MUST be used with expensive and complicated third party software. There is no capability with the included web interface to even set up simple on/off control of IR devices. Global Cache had the opportunity to build a really great product but is simply missing the point by not including any practical application capability with the IR2IP. If you don't have the required software already, there is absolutely no point in buying this item.