Winkelwagentje

Winkelwagen is nog leeg.

Winkelwagen is nog leeg.
Op voorraad
5/5
5 Recensies

IMX219 Camera Module met FOV62 M12 Lens voor Raspberry Pi, Jetson Nano, Jetson Xaiver Compatibel met Raspberry pi Camera v2 (PI-CAMV2-FOV62)

3,99€ 9,00€
Gratis verzending bij bestellingen boven 25,99€

1.Kleur:Pi-camv2-fov62


Productdetails

  • -Compatible with raspberry pi camera v2;
  • -Support Raspberry Pi and Jetson Nano;
  • -M12 Lens FOV60/FOV90/FOV160 Options;
  • -1x15PIN FPC Cable;-1x22PIN FPC Cablle;
  • -Only need to set dtoverlay=imx219,camera_auto_detect=0 on config.txt;


Productbeschrijving

Pibiger Raspberry Pi camera V2,8M Pixel IMX219 sensor M12 FOV60/90/160 graden lens voor Raspberry PI,Jetson Nano

Belangrijkste

Producteigenschappen:

Ondersteuning Raspberry PI5/Pi4/PI3+/PI3/PI2/PI0/CM4/CM3+/CM3/Jetson Nano; grootte 32 mm x 32 mm; Options lens voor FOV62, FOV90, FOV160Packing lijst:

1 x cameramodule

- Camera-lens

—15-pins naar 15pin fpc-kabel;

—15-pins naar 22pin fpc-kabel;

Specificaties:

Beeldsensor IMX219
Still Resolution 8 megapixels
Sensorresolutie 3280 × 2464 pixels
Videomodi 1080p 47fps, 1640 × 1232p41fps, 640 × 480p 206 fps
Pixelgrootte 1,12 µm x 1,12 µm
Optische grootte 1/4 inch
IR-cut ja
Afmetingen module: 32 x 32 mm
Lens FOV60, FOV90, FOV160 Options

Quick Start For jetson nano,jetson Xavier NX

Step 1: Open the terminal and execute the following

  • sudo /opt/nvidia/jetson-io/jetson-io.py

Step 2: Select Configure Jetson Nano CSI Connector

Step 3: Select Configure for compatible hardware

Step 4: Select the camera that you want to use

  • Camera IMX219 DUAL

Step 5: Select Save pin changes

Step 6: Select Save and reboot to reconfigure pins

Step 7: Press any key on the keyboard and the device will reboot with the applied camera configuration

For CAM0 port

  • nvgstcapture-1.0 sensor-id=0

For CAM1 port

  • nvgstcapture-1.0 sensor-id=1

Quick Start For Raspberry PI

Step1, Modify config.txt

  • sudo nano /boot/config.txt

For the latest version raspberry Pi OS, it should be /boot/firmware/config.txt

Step2, Add below content to the last line

  • dtoverlay=imx219

Step3, Reboot and use below command to preview

  • libcamera-hello -t 0

le bûcheron
9 augustus 2025
Sur RPi Zero 2 W avec raspios bookworm 231211 arm64 lite,la seule chose à faire est d'insérer la lignedtoverlay=imx219dans le /boot/config.txt (et rebooter)
Marco B.
28 mei 2025
Usata assieme a Raspberry pi 4B per klipper su una stampante 3D, fino a 30 fps video stabile, oltre ha dei problemi.Plug 'n paly.
JJ
19 maart 2025
There's a lot of fun little projects you can make with this and a raspberry pi, and a few other things usually. I ended up making a magic mirror following instructions I found online. The camera worked great. It shows a pretty good picture. The rest of the project, making the magic mirror, etc... that took quite a bit more work, but nothing too crazy.The camera is easy to connect to a raspberry pi on the pins on top. Then you just need to find some instructions for how to make it interface with the RPi, and do whatever it is you're trying to do... will probably take a little bit of python coding, or something similar. but most of the things this would be used for have already been done, so you can find the code online and copy paste it.
Alvaro de Castro
18 maart 2025
DOES NOT WORK WITH NVIDIA JETSON NANOIT DOES NOT SHOW UP AT /DEV/VIDEOGARBAGE, DON'T BUY
osama
19 december 2024
Camera did not work with Raspberry pi zero W, Raspberry pi zero W and Raspberry pi 5

Misschien vind je dit ook leuk