KATSU Zakgat-sjabloonset, draagbare perforatie-sjabloonset voor houtbewerking, gereedschap voor het lokaliseren van gaten, met boren en schroeven 105418

Deze pockethole set werkt, maar gat afwerking is slecht en afstelling is lastig.Ik ben overgestapt naar een simpele KREG pockethole jig en deze werkt een stuk makkelijker en geeft mooi afgewerkte gaten.

De media kon niet worden geladen.

تقليد صينى ىسيء لركه كويسه و غاليه جدا على مستواها

After watching lots of reviews and considering budget bought the Katsu Pocket Hole Jig. On opening the box very impressed at the quality look, worked through the manual that came with it but just a bit of advice watch visoes of how to use a pocket hole jig. Have to say on reading some of the poor reviews this got I cannot see why, this product is well made, yes one hole is slightly lower than the other as may be less than 1mm, but then if I wanted perfection i would spend a lot more money on a tool, that said the tear out that you get is the same as apparently the more expensive one according to the video reviews. Currently I have just practiced on off cuts but I have to say I am impressed with the results, will post further information when used on a build project.Early reviews say the drill guides are the wrong way around but think this must have been just early modes as they are correct now, well unless I am using it wrong!!What comes in the box? The aluminium jig(I mounted to my work bench) a drill bit and collar, square screw driver allen key, a bag of pocket hole plugs, a bag of 1&1/2 inch screws with flat heads. that can be screwed in using the square driver or a phillips head driver. L=shape adapter for off the jig pocket hole cutting. 2 allen bolts to raise the 1/2 inch wood to the correct position for pocket hole drilling. It was mentioned in a review that you cant use 38 mm wood as jig wont lock it down, I found the same but used a shorter bolt to get a round this and for the cost of the jig don't have an issue with that.Overall so far soo good and am pleased that I purchased this, will update on longevity of the product as I use it.Update 18/02/21Having now used this on my latest project I have increased my review to 5 stars, having practised using it and using on my latest project I am so pleased with this item and can recommend it without any hesitation. Take your time when drilling lifting the drill in and out while using rather than pushing the drill down in one move, better finish, the wood does make a difference to the result if rough wood the rip will look bad no matter what type of pocket holer you use, I have used on planned wood purchased and rough wood that I planted myself and both resulted in a good result.

Concordo con le recensioni precedenti e aggiungo 2 cose che ho notato da subito.1) se non si regola bene il pressore al pezzo a L(elle) avvitato con 3 viti dove c'è la manopola potrebbe arrivare troppa forza e flettere un pochino (perdendo i 90°), servirebbero altre due viti sulla aletta che poggia sulla base oppure regolare adeguatamente il pressore. **Aggiornamento: flettono tutti e non influisce sul risultato finale.2) ho notato che ci sono 2 coppie di fori da usare in base allo spessore del pezzo 12-19-25mm e 30-38mm ma le indicazioni stampate (vedi foto articolo) POTREBBERO essere INVERTITE cioè dove ce stampato 12-19-25mm in realtà sarebbe 30-38mm e viceversa. Questo perchè su youtube girano due versioni identiche ma uno con indicazioni in mm e l'altro con indicazioni in pollici (inc) MA NON CONCORDANO, nel punto dove c'è scritto 12-19-25mm nella versione in pollici c'è scritto 1¼" e 1½" di conseguenza dove nella versione in millimetri c'è scritto 30-38mm nella stessa in pollici c'è scritto 1/4" 1/2" 1". Verosimilmente credo che quella in pollici sia veritiera ma potrei sbagliare. ciao**Aggiornamento: Si. Sono invertite basta osservere le immagini nel libretto delle istruzioni a corredo, quella in pollici è quella giusta.

Ürün bayağı sağlam duruyor, kullanma durumum olmadı ama ben şahsen beğendim teşekkürler Amazon

Es espectacular