Micro Swiss All Metal Hotend Kit voor Creality CR-10 / CR10S / CR20 / Ender 2, 3, 5 Printers

Super produit maintenant je peux imprimer à l'aise l'abs. Cr10 d'origine monte à 260 c'est parfait. Avant le ptfe cramais et ca bloquait le filament.je recommande.

Worked like a dream.Before installation I was getting a number of blockages in the hotend due to heat creep and couldn't get rid of it no matter how much a mucked around with the slicer and wasted half a role of filament attempting to dail it in.Bought this and it was essentially plug and play and with a bit of PID test and tweeking, it worked brilliantly

Non volevo assolutamente spendere così tanto per una hot endHo acquistato tre cloni low costNonostante varie modifiche, prove di settaggi infiniti e un’enorme perdita di tempo, questi cloni non hanno mai funzionatoIl problema era l’intasamento e la continua variazione della portata (flow) anche cambiando vari ugelliQuesto della swiss è perfettoMigliorata la stampa, flow costanteRiesco a stampare pet senza fondere il teflonMontato su CR-10S4 con modifica ad estrusore direttoConsigliato

Here I will attempt to give my Experiences an Impressions of the MicroSwiss Hot End!.First I was a bit surprised its called Micro Swiss but its made here in the U.S.?????But We Live In The times We Live In Right!.First off I must say it is a Very Good Unit for as a young fella i had toolshop training and i have to sayin quality the Unit i received was first rate .Now I received My Order quickly so as usual both Amazon and the Seller has their act together and i can only say 'Good Going' guys on the shipping, You did well!...TO INSTALL:I wont go into 'Great Detail' here as their are YouTube videos that explain the detail better then i can.Put simply if you have simple tools most Americans have, And you are capable say of fixing a Kitchen Faucet then you should be able to assemble and mount a MicroSwiss Hot End to a Ender Printer ,.'Now This Is A Balancing Act as Its Important to understand the Pluses and Minuses!'...See My problem was My Bodwin tube melted and started causing my hot end to leak!!!!!.Granted I couldn't see re-placing this with a factory unit, So i bought a MicroSwiss and a newHigh Temp tube!.....So if you are buying this to replace a Bad or Worn or a Defective Hot End then this is a deal for you!...But if you ARE buying this just to increase temps so you can process NYLON or Hi Temp materialsthen 'This Part' alone cannot help you!.In fact it was a 'Bad Disappointment' to find despite adds to the contrary!...Yes and truly Micro Swiss is a top grade part and is an improvement over the factory Hot End!.And i definitely like the way my parts are coming out now, But in truth it only adds about 5 degrees to my operating temperatures!.This Part Does NOT Automatically of itself INSURE that 'Your Machine' will run NYLON!.In Truth Its Kinda A Half and Half Thing!.Most Folks are buying this or something 'like it' for 'Ender Printers' to increase Melt temperatures!.But due to Computer Settings and P.I.D. Enders are 'Locked Down' to 260C O.K.Plus the Heat Block on the Micro Swiss is plain Aluminum and not the Stainless Steel I was hoping for.As that alone "drastically" limits Operating Temperature.Please remember THIS is not a fault, It is simply the way that part is designed to run/operate!.Very Fortunately I Dont have to run Nylon in my normal work!.Yes if i changed the 'Junk Aluminum' block with a Copper Block which Amazon carries that could possibly kick me up towards 270C which would make it more realistic to run some of the newer Nylons that Amazon is currently listing and those are Quality Goods!.Now with a 'Stock Hot End' I ran 'Taulmans 230' which is a low temp NYLON and it turns out some fine parts that has to be said, But i must also point out its not Rock Hard but its good for use where toughness is needed but some flexibility is allowed,.To Close let me state that the MiscroSwiss is good and a fine choice to replace worn and bad parts as it certainly does a fine job in the normal temp range the Machines. were originally designed for!.But clearly DONT buy an ENDER if you intend to run NYLON as that machine simply isnt set up for it!.Yes some people try altering PID or tampering with the computer code and have wound up damaging their machines.Buy a Prusa or a different make which is more Modern and Up to Spec!.But for my uses MicroSwiss makes a fine part, it installed easy, Runs fine and does its Job!.Recommended!IndianaED

As described