Opblaasbare Spa Whirlpool reparatieset Lay Z Spa

Man soll den aufgeklebten Flicken 24 Stunden lang ganzflächig beschweren, bis der Kleber ausgehärtet ist. Das ist bei einem aufblasbaren Pool an manchen Stellen nicht zu händeln. Zudem blieben unter dem Flicken Lufteinschlüsse bestehen, die später einen Weg schafften, daß der Pool wieder Luft verliert. Es wäre aus meiner Sicht besser gewesen, einen dickflüssigen Kleber zu haben, den man großflächig aufträgt (ohne Verwendung eines Flicken), der innerhalb weniger Minuten aushärtet. Aber naja; ich habe nunmehr den teuren Pool entsorgt, weil ich ihn nicht mehr abdichten konnte.

I was setting up our metal frame pool (12' x 39") when I noticed that not only was a previous self-adhesive repair on the base falling off, but there was also a new 1.5" cut near to it.Because of this I decided to try a more permanent repair and after reading reviews I decided to give this kit a try.The result is two repairs that I feel really confident about. The kit comes with full instructions and if you follow them you will do a good repair. But below is a list of tips that will help you make an even better repair.....1 - make sure that when you cut your patches to size they have fully rounded corners.2 - do NOT skimp on the patch size.3 - do NOT skimp on the adhesive.4 - be ready because when you apply adhesive to the patch, the patch will start to curl up.5 - totally clean and degrease a good distance around the hole/tear (pure alcohol is great for this).6 - if at all possible apply a repair to BOTH sides of the hole/tear.7 - the cotton applicator is good for one session only as it goes hard afterwards. So maybe have a stock of large cotton buds on hand if you need to fix new holes.In short this is a really good and effective repair kit and I am confident that my repairs are permanent.

I originally bought this repair kit because it was recommended to me by a hot tub rental company company when we bought one of their Lazy Spa's off them second hand. It is inevitable that if you own a Lazy Spa or similar, it will pick up a puncture from time to time but this kit gave us long lasting and reliable results.You get plenty of the material used to cover the punctures and the glue itself doesn't take long to dry. The applicator itself is a bit of a one hit wonder because once you've used it, the glue goes hard on it which then makes it a bit harder to use but it's a minor gripe in what is overall, a very good product.Our hot tub did eventually reach the point of becoming unrepairable but that's always going to be the downside of the cheaper inflatable hot tub when compared to the much more expensive hard shell versions.I think if you have an inflatable hot tub then this is a must have product and would recommend.

Unexpectedly excellent product. Some of the other packs are a bit cheaper but they have nowhere near as much glue and vinyl patch material. This has 60ml (2 fl.oz) of some quite potent glue which is wickedly sticky stuff to use. My pack contained a roll of vinyl maybe 15cm wide, more than 30cm long, and two sheets.On the down side, the vinyl is quite thin - thick enough to patch our airbed, but this combined with the glue itself does make getting the patch in place a bit tricky (the glue deforms the vinyl within seconds). So four stars instead of five. I think with slightly thicker vinyl, this would completely merit five stars.Having had to patch four tears on the plastic welds on our airbed, I found the best way to use this stuff was to cut a decent size patch (I'm allowing 2cm in all directions beyond the hole), flatten it out on a marble pastry board or a piece of cold glass/mirror, put a decent blob of glue in the centre, then use a spatula or spreader to cover the entire patch. Try to keep it flat on the board because it will try to lift and curl a lot. You must get enough glue spread to the very edge of the patch or the curling of the vinyl will prevent the edge from sticking. Place the patch on the repair area quickly, then while avoiding getting glue on the top of the patch, press out all the air and then keeping pressing the edges down. Take a couple of extra minutes doing this and you get a much better patch with no raised edges. (The glue once dry rubs off the mirror/marble really easily and cleanly.)I've let the glue dry for the required 24hrs and so far all four patches have held perfectly even with adult load on the air bed.If you've a big tear to cover, I'd be tempted to double patch i.e. patch once, let it dry, then patch again with a larger piece, since the vinyl patch material is relatively thin and flexible.On the downside, the glue itself is heavy duty stuff with a lot of solvent so it attacks the material being patched. On the lighter weight vinyls of airbeds and inflatable toys, this can be a challenge so don't overload the glue - it's a difficult balance to get. If you have something heavy, flat and non-adhesive like my upturned marble pastry board it is well worth leaving this pressing on the patch for several hours to reduce the rippling, as advised on instructions. I finally got my fourth patch about right in terms of glue, speed, flatness, bubble-free, etc, so if the cosmetics are important, I would definitely practice somewhere first. I don't think you would get this problem with a heavier duty vinyl.

Great for fixing repairs on my hot tub. Works great and last for ages. Great buy, I'll be repurchasing some soon because I don't want to be without it. Each repair I have done with this has lasted. It sticks really well. Covers different types of holes or slits