Winkelwagentje

Winkelwagen is nog leeg.

Winkelwagen is nog leeg.
Op voorraad

Rain Bird Wifi-module voor draadloze bediening

63,99€ 135,00€
Gratis verzending bij bestellingen boven 25,99€

Over dit item

  • Rain Bird ESP-TM2-controllers en ESP-Me-controllers die na 2 november 2016 zijn geproduceerd.
  • ESP-Me-controllers die vóór november 2016 zijn geproduceerd, kunnen door de aanschaf van een nieuw ESP-Me-upgrade-paneel (apart verkrijgbaar) worden opgewaardeerd om deze module te accepteren
  • Steek gewoon de LNK wifi-module in de accessoireaansluiting op de voorkant van een compatibele controller
  • Gebruik je tablet of mobiele apparaat om irrigatieplannen in te stellen, te bewaken en wijzigingen aan te brengen
  • Internationale producten hebben aparte voorwaarden, worden vanuit het buitenland verkocht en kunnen verschillen van lokale producten, waaronder pasvorm, leeftijdsclassificaties en taal van het product, etikettering of instructies.


De Módulo WiFi LNK is uitgerust met een los gebruik van functies en een ESP-RZXe-programma op afstand van een ESP-Me of ESP-RZXe de Rain Bird een accessoire en een smartphone met ondersteuning voor Apple, iOS of Android en accepteert een internet.


Karl-Heinz B.
7 juni 2025
Die zahlreichen Hinweise über eine teils recht schwierige Inbetriebnahme kann ich bestätigen. Bei mir war es so, dass ich zunächst den Rain Bird Controller RZXe ohne WiFi-Modul betrieben und manuell konfiguriert habe.Die Installation der Rain Bird App auf dem Handy lief problemlos, jedoch kam zuerst keine Verbindung zw. Handy und Controller zustande. Nach zahlreichen Neustarts des Controllers funktionierte es endlich, doch wurden die über die App eingestellten Werte nicht übernommen. In einem Blog habe ich gelesen, dass der Zugriff auf GPS in der App freigeschaltet werden muss und ja, danach war eine Kommunikation zw. Handy (Android 12) und Controller möglich. Es ließen sich jedoch keine Netzwerkparameter für das WLAN konfigurieren und plötzlich funktionierte auch das Passwort des Controllers nicht mehr.Lösung: Reset auf Werkseinstellung. Danach ließ sich alles problemlos einstellen und auch die Kommunikation über das WLAN funktionierte sofort. Es erschien jedoch immer wieder die Meldung, dass das WLAN-Signal zu schwach wäre?! Der Router steht nur 5m vom Controller entfernt. Und auch die Abfrage der WLAN-Signalstärke in der App zeigte "stark". Ist wohl ein Bug.Die App ist selbsterklärend und funktioniert gut. Sogar die Beregnungssteuerung über die Wetter-App funktioniert tadellos und reduziert die Beregnungszeiten je nach Wetterbedingung. Über ein VPN läßt sich der Controller auch außerhalb des eigenen WLAN steuern und überwachen. Sehr praktisch während des Urlaubs.
Malezieux
18 april 2025
Bon rapport qualité prix et livraison rapide
Doug D
12 april 2025
Simple easy to follow installation, worked like a charm straight from the start. The internet connection factors in outside weather reports when following set irrigation schedules, putting watering on hold if rain is reported.
rd
26 maart 2025
I upgraded the faceplate on my ESP-Me to be the new wi-fi enabled, and added this module to the faceplate. I downloaded the Rainbird app onto my tablet and after setup, I am now able to access the ESP-Me controller from the tablet. As of November 2016, Rainbird has offered the ESP-Me wifi accessible controller. The older version ESP-Me pre November 2016 faceplate only, can be replaced with the new wifi version faceplate. Then this wifi module can be plugged in the back side of the new faceplate. It took me less than 20 seconds to swap out the faceplate and I already had the wifi module plugged in the back side of the new faceplate. It took me less than 20 seconds to swap out the faceplate and I already had the wifi module plugged into the new faceplate. Disconnect the small ribbon cable, and then put some pressure on the left side hinge to clear the tab the other end is seated in, put new faceplate in and replace the ribbon cable. The new faceplate has a wifi ready symbol in the lower dark green area. My only issue was getting a wifi signal strong enough to the controller.I had to move my wifi extender in the house closer to where the Controller is mounted outside on the house. Also you will need your router password for one of the setup entries. I lost mine, but I was able to retrieve it off one of my connected devices by following a youtube tutorial.Download the Rainbird app from the iOS version 8 or greater, or Android device 4.4 kitkat or later, fill in each step. You will be filling in zip code and also your wifi password, a password to remotely access controller, name of location (optional), etc. In the video one guy said if you are old you can use a tablet or ipad. I did everything on my Samsung 10" tablet. I can now see my program(s) on the tablet. I can name each zone, (front west drip, etc), see the time each zone will come on, run a zone manually, change run times, see the total time those zones will run on each program, lot's of features, and you can take a picture of the area and upload it.I am glad I can remotely access the controller. One picture shows all entries added accessed by touching the pencil on the first screen, the second pic shows zones and if a zone is running, see zone 13 access by touching the drip symbol on the front screen.
Elrodri
17 december 2024
Con este equipo vuelves inteligente el riego, cale la pena aunque ya hay nueva version