Redrex Ender 3 V2 Bowden Extruder 40 tanden MK8 Drive uitrusting voor Creality Ender 3 Pro, CR-10, Ender 5-serie en andere verwarmingsplaat Prusa 3D-printers

Werkt goed, let op er is een set die meer onderdelen bevat en goedkoper is

De extruder past perfect op de motor van mijn Ender 3, zelfs met de direct drive die er op geinstalleerd zit. Het metaal voelt erg stevig aan, en hoop er nog veel mee te kunnen printen!

I am happy I bought this bowden extruder. It works perfectly. Qood quality.

I bought it because everyone recommends it. Luckily I did, because the plastic stock one broke on two places. At first I was a bit skeptical, but after using it I immediately saw a different result. The result is small, but it is noticeable. By installing this extruder I almost got rid of my under extrusion problem.

Ik heb de Extruder gebruikt voor mijn Ender 3 V2. De materialen zijn van goede kwaliteit en zijn binnen afzienbare tijd geleverd.De handleiding is in principe duidelijk maar had iets uitgebreider gekunt. Een advies aan REDREX zou zijn om in de handleiding ook te beschrijven hoe de bestaande extruder verwijderd moet worden, dit scheel wat tijd.

L'ho comprato per aggiornare il mio clone di prusa. Stó montando un estrusore tipo bowden con hotend V6; usato con il motore originale, facilissimo da montare, le istruzioni sono delle foto passo passo... quindi impossibile sbagliare. È tutto in alluminio, robusto e veramente ben lavorato e rifinito. Per il prezzo pagato e la velocità con cui l'ho ricevuto credo di aver pagato il giusto. Consigliatissimo come ricambio o come ho fatto io per upgrade. Comprato dal venditore Redrex3d.Spero di essere stato utile.

S'installe très bien sur une Discoeasy200 Dagoma en remplacement de l'extrudeur d'origine.Permet d'avoir le levier côté arrivée filament (plus pratique), fonctionne avec pression ressort au minimum. Ai dû raccourcir de 2 mm le sommet du levier qui frottait légèrement sous le plateau (facile, quelques coups de lime). Embellit mon imprimante, extrudeur parfait pour mon usage.

Really good quality of the parts! Also looks very nice. Please nore that its recommended to put some nutlock fluid on the screws for the spring.Fast delivery!I totally recommend this seller!5 stars!!!

The Redrex Aluminium Bowden extruder upgrade is a really in-expensive and straight forward upgrade from the stock plastic extruder that comes on the Ender 3d Pro, which was the printer I bought this to fit. It`s red powder coat looks cool too and breaks up the black.Please note this kit is upgrade for the extruder part of the motor and does not come with a motor.It came with clear instructions and can be fitted using the tools that already came with the Ender 3d pro so no extra equipment required. It took about half an hour to remove the old one and fit this one. there was only I snag. The feeder gear on my motor is pressed on, unlike older ones that are held in place by a grub screw on a flat surface, so it could not be slid off so I did the upgrade but did not use the brass gear supplied with it nor did I need the metal bracket on my printer. the filament outlet on this part is also upgraded from brass to steel which should also reduce wear and friction.The plastic extruders are known to wear quite quickly and on occasion break when the lever is compressed to release the filament, this upgrade is sturdy and eliminates the chance of that happening all in all a good upgrade that will only enhance future printing.

muy buen material en comparación con el de plástico que tenia, que se rompió, fácil de montar y a funcionar sin problemas.