Winkelwagentje

Winkelwagen is nog leeg.

Winkelwagen is nog leeg.
Op voorraad

WINSINN 50mm Ventilator 24V 5015 Hydraulische Lager 50x15mm Turbine Turbo - Hoge Snelheid (Pack van 4 stuks)

5,99€ 12,62€
Gratis verzending bij bestellingen boven 25,99€

1.Kleur:5015 24v


Productdetails

  • ✔️Hydraulische lagers 5015 ventilator met hoge snelheid
  • Hoge kwaliteit hydraulische lagers, beter dan olielagers, stabieler en lange levensduur, geschikt voor continu werk. De levensverwachting is ongeveer 45.000 uur.
  • ✔️️Nominale spanning: DC 24 V
  • ✔️️Afmetingen: 50 x 50 x 15 mm
  • ✔️️Gemaakt door WINSINN


Productbeschrijving


► Hydraulische Lagers - Hoge snelheidsversie
► Hoog - kwaliteits Hydraulische lagers, Beter dan Olielagers, stabieler en Met lange levensuur, geschikt voor het ononderbroken werk. De levensverwachting is ongeveer 45.000 uur.
►Grootte: 50x50x15mm
►Nominale spanning: DC 24V
►Lijnlengte: ongeveer 30 mm
---------------------------------------------------------------------------------------------------------------
Inhoud van de verpakking:
►4 x Hoge snelheids Hydraulische Lagers 5015 24V Ventilator Ventilator
---------------------------------------------------------------------------------------------------------------------
Product Garantie:
-WINSINN is toegewijd aan het aanbieden van hoogwaardige producten aan alle gekoesterde klanten. Ondertussen levering 60 dagen geld terug garantie en 24 maanden garantie.
-Als er vragen zijn, neem dan gerust contact met ons op, WINSINN Customer Service Team zal geen moeite doen om u binnen 24 uur te helpen.


Hans van den Hoek
20 juni 2025
Really high flow fans w/o too much noise.In use on my extruder (3d printer)
Onur
19 mei 2025
Using dual 5015 fan duct with this, workes nicely. But makes rattling sound when the printhead moves because the ball bearings are not fixed. As expected.My printer is now more quiet and cools better.
Geobig
15 mei 2025
Used as a part cooling fan in FDM printer. Great airflow - not too noisy - however if the rotor is blocked from turning by a bit of debris, or if the fan air output is blocked, the unit will overheat to the point of melting the fan housing. Also if running with a ambient temperature over 40C under load the fan will suffer damage (rear of housing melts). Power is 3 watts at 24V
Micke 392
7 februari 2025
Achetés pour remplacer les ventilateurs d'origines de mon imprimante 3D je suis bluffé car ils sont hyper silencieux et je trouve qu'ils soufflent très fort donc attention à vos réglages.Je recommande!
Chickendownunder
10 januari 2025
they really BLOW
Favrel
27 november 2024
I tested only one so far, others are spare.Works great.Edit after futher testing :I have compared it to others fan of same size with respect to flow and static pressure.This blower is indeed the quietest but provides the lesser flow and pressure. I recommend it only if you need low noise and that you dont need big airflow performance. For 3D printer, if the airflow is not too much restricted and the fan not too far from the object to cool, it is totally fine. Direct blow without fancy air duct is best.In my application where i need the airflow pushed though a filter, this blower is too weak so i will use others.
Carole Langan
20 november 2024
Small but powerful, I use them in my fursuit heads.