Winkelwagen is nog leeg.
Winkelwagen is nog leeg.Productbeschrijving
Item Beschrijvingen:
-100% gloednieuw.
-1/2" Krukas Sleutel
-compatibel met:
Honda/Acura
Accord 2,2L 4Cyl 90-97,2,7 L 6Cyl 96,2,3 L 4Cyl 98-02,2,4 L 4Cyl 03-16,3,0 L V6 98-16
Civic 1,6 L 4Cyl 92-00,1,7 L 4Cyl 01-2016,2,0 L 4Cyl 03-nieuwer
Piloot 3,5 L V6 03-16
Ridgeline 3,5 L V6 06-16
Inzicht 1.0 L 3Cyl allmodel
S2000 2,0 L 4Cyl 00-03,2,2 L 4Cyl 04-16
CL 2,2 L 4Cyl 97,2,3 L 4Cyl 98-99,3,0 L 4Cyl 98-16
RL 3,5 L V6 96-16
Odysey 2,2L 4Cyl 95-97,2,3L 4Cyl 98,3,5L V6 99-16
CR-V 2,0L 4Cyl 97-01,2,4L 4Cyl 02-16
-Element 2.4L 4Cyl 03-16
Preludium 2.2L 4Cyl 92-01,2.3L 4Cyl 92-96
Delsol 4Cyl 93-97
Integra 1,6L 4Cyl 90-92,1,7L 4Cyl 92-93,1,8L 4Cyl 93-01
TL 3,2 L V6 95-16
NSX 3.0 L V6 91-16 (Past niet op alle motor), 3.2 L V6 98-16
Pakket:
Krukas Sleutel x 1
Artikelspecificaties:
Materiaal: staal
Diameter gat: ca. 42 mm/1,65 ¡±
Aandrijving:1/2¡±
Land/
Type: krukassleutel
Grootte:
Systeem van meting:
Aantal stuks: 1
Kenmerken:
Garantie: Ja
:
Ebo Eppenga
13 juni 2025
Werkt prima om de krukasbout van een Honda vast te zetten. Let op, is wel ietsje aan de kleine kant waardoor je wel even moet kijken of het goed vast zit. Maar doet zijn werk prima!
T. Mcilwain
6 mei 2025
This absolutely does the job its a good fit well made and very reasonably priced, manual says loosen engine mountsto drop engine 50mm for access to bolt but didn't have to this goes in at an angle and if you fit the breaker barinto the back of the the 1/2" square hole ie engine side, the bar will wedge between wishbone and chassis then on the 19mm bolt I just used the ratchet with a cut off section of an old trolley jack handle to extend the handle position yourself lengthwise with the car and push ratchet handle with two feet (car is well secured on axle stand) Bob's your uncle
Danish Latif
5 mei 2025
The tool could fit better as it’s not as “snug” as you’d expect it to be. However it did its job perfectly as it held the pulley in place via a bar anchored to the ground, while I was able to loosen a stubborn bolt with a second car. Invaluable tool, helped me where an impact did nothing.
Tonto
3 april 2025
As described.
David A.
16 februari 2025
Good fit in Honda Accord crank pulley, quality forged steel.1/2" drive ratchet lines up nicely with front lower suspension arm to brace it while having at the pulley bolt - N.B. pulley bolt will need *huge* anount of torque to remove, probably close to 400 lb-ft! Maybe more!
abbott
13 december 2024
Would not buy this as the materials are subpar at best
Aanbevolen producten
Misschien vind je dit ook leuk