Digitale snelheidsmeter OBDII KMH/MPH overmatige snelheid, automatisch alarm, frequente foutcode, scanner met lcd-display voor 12 V, de meeste dieselvoertuigen

Happy with the purchase-Works great.

Para Toyota Prius 2010 funciona genial, marca la temperatura de agua.

Mit diesem Produkt konnte ich das Problem mit den schlecht ablesbaren Instrumenten in unsern Citroen Jumper Kastenwagen lösen. Einfach anschließen, Einheiten einstellen, läuft.

The Autool x50 PLUS works perfectly with my 2008 Honda Pilot (OBD Type ISO 9141-2).It was delivered fast and looks great and is very simple to hook up, just one connection. The display has an auto turn on, it turns on when you start the car and an auto shutoff, shutoff time is adjustable up to 20 minutes after the car is turned off. The display is easy to see, day and night. The brightness level, is controlled by a light sensor and it is not manually adjustable. I have mine is setting in front of my instrument panel and the display brightness is just fine day or night. After installing the Autool x50 PLUS, I had some question, So, I emailed the seller “OBDIIShop” and they replied as quickly as hour later a couple of times, BUT, never longer than 24 hours, they appear to be closed on the weekends. The reply emails were very helpful in answering all my questions. Their customer service is great!The Autool x50 PLUS has Lots of customization options. The X50 PLUS has four area’s/positions on the main display. The Position 1 (Largest read out) can display MPH / Km/H speeds, coolant temperature in F or C, Fuel in MPG or LPH and many other read outs are available by just by toggling the switch below the display to the left or right. Position 2 and 3 (Smaller readouts in center left and right of display) can be configured to show multiple different measurements (Position 2 and 3 only display metric units NOT US/imperial units), I did not find this an issue because, I have mine set for Voltage and Engine RPM, Position 4 only can configure instantaneous fuel consumption or engine rotation progress bar display.I used mine mainly for Speed with the Speed Alarm on the Position 1 and MPG, (to prevent a heavy foot during acceleration) on the progress bar display. Both the large/primary and the progress bar display can easily be seen with a quick glance. The MPH speed alarm setting can be set in the Menu “Settings” under OverSpeedSet”. The easiest way to set it, is to convert the MPH you want the alarm sound at (use the internet for conversion), to Km/H and enter that speed into the ”OverSpeedSet”. The nicest thing about the speed alarm is the speed readout changes from white to red when you go over the speed alarm limit. If you don’t want the alarm to turn on just set it to 160 that is 99.41MPH, or use a higher number if you drive fastest than this.AVG and Current MPG are accurate, BUT you will need to go into the setting menu and make sure your “Engine Size” is correct and the “KPH” is set show your correct vehicle speed in MPH or Km/H which ever one you use while driving. After that you need to go through a few gas full ups and manually figure you gas mileage and then adjust the “Fuel Adjust %” in the menu settings, the more you do this, the AVG and Current MPG / Km/H Display will be more accurate. You have to do this even with “SCAN GAUGE”. I also have a SCAN GAUGE, but for information at a quick glance, the Autool X50 PLUS can’t be beat.“OBD Diagnose” lets you read and reset OBD scan codes, also you can read the real time active data that is available to your OBDII port, just go to Menu, “OBD Diagnose”, “DATA Stream”. It is great way to see why your Check Engine light is on.There are a lot of features in the Autool x50 Plus and I haven’t used them all, like the “Driving Test” Menu that check braking time and distance and Speed test.

2021年型アクアに取付けしました。以前の車から10年程使っているデジタルモニターの表示が点滅し出したので、寿命と思い代わりの物としてこれを見つけました。すべての機能を試せないほど多機能で表示も見やすく、価格もリーズナブルであると思います。設定などはかなり修正する必要があるので、主な設定の修正点を参考までに記載させていただきます。①表示単位(アメリカ向けになっている) UNITを 「imperial」から「metric」に変更。②エンジン車では必要ありませんが、HV車ではエンジンが停止するとすぐスリープ状態になるので、スリープ時間を２０分に変更。(但し、電源はOBDからではなく、ACCから取るように改造しないとバッテリ上がりの心配があります。)③スピード表示が車載メータとずれている場合、パラメーターを変更。④水温などの表示画面で下の棒グラフは初期設定で「燃料消費量」になっているので、エンジンの回転数を表示したい場合は変更。⑤付属の両面テープでは固定しにくいので、粘着シートなどを使う。★４つにしたのは日本語の取説が無いためです。英語の得意な方は問題ないかと思いますが、普通は英語の取説を読み解くのに苦労します。