Winkelwagentje

Winkelwagen is nog leeg.

Winkelwagen is nog leeg.
Op voorraad

LIBRATON 3/8 'Drive Lange Impact Hex Bit Socket Set, Allen Bit Sockets, S2 Staal Hex Head Sockets, 20 STKS Inbussleutel Socket, SAE & Metrische Inbussleutel Set, 6 'Lange Inbussleutel Sockets, Blow

25,99€ 53,00€
Gratis verzending bij bestellingen boven 25,99€

Productdetails

  • Hoge kwaliteit: De impact Hex bit socket set is gemaakt van S2 gelegeerd stalen bit plus CR-V stalen socket, wat zorgt voor verbeterde schokbestendigheid, slijtvastheid en duurzaamheid. De mangaanfosfaatcoating beschermt effectief tegen roest en corrosie, waardoor langdurige prestaties worden gegarandeerd.
  • Extra lengte: De extra lange inbussleutel bits zijn 6 inch (150 mm), wat een extra bereik biedt voor bevestigingsmiddelen die zich in verstopte en smalle openingen bevinden.
  • Impact Design: het dopdeel is ontworpen met een slaggat dat past bij zowel slagmoersleutels als handsleutels, waardoor de inbussleutel slagkrachten kan doorstaan, perfect voor doe-het-zelfprojecten, mechanisch onderhoud en zware taken.
  • Nauwkeurig & Variëteit: De Hex bitkop is ontworpen voor een veilige grip en minder slippen, wat zowel de efficiëntie als de veiligheid tijdens het gebruik verbetert. De inbussleutel set bevat metrische (3 mm tot 12 mm) en SAE (1/8" tot 7/16") specificaties om aan meer werkbehoeften te voldoen.
  • Hoog rendement: de 3/8 inch drive inbusset is netjes opgeborgen in een geblazen doos, waardoor de inbussleutten georganiseerd en gemakkelijk toegankelijk blijven. Elke Hex socket is voorzien van duidelijke lasergeëtste maatmarkering, zodat u snel de vereiste socket kunt vinden en de werkefficiëntie kunt verbeteren.


Productbeschrijving

LIBRATON 3/8" DRIVE EXTRA LONG IMPACT TORX BIT SOCKET SET

KENMERKEN:

De Hex bit socket set is gemaakt van S2 gelegeerd staal bit plus CR-V stalen socket, zorgen voor verbeterde schokbestendigheid, slijtvastheid en duurzaamheid.

De mangaanfosfaatcoating op de inbusdoppen beschermt effectief tegen roest en corrosie, wat zorgt voor langdurige prestaties.

Het dopdeel is ontworpen met een slaggat dat past bij zowel slagmoersleutels als handsleutels.

De hoge kwaliteit van de impact Hex socket set maakt het mogelijk om slagkrachten te verdragen, perfect voor professionele projecten, mechanisch onderhoud en zware taken.

De Hex bitkop is ontworpen voor een veilige grip en minder slippen, wat zowel de efficiëntie als de veiligheid tijdens het gebruik verbetert.

De inbussleutel socket set bevat metrische en SAE specificaties zijn beschikbaar om meer werk behoeften te voldoen.

De extra lange inbussleutel bits zijn 6 inch (150 mm), waardoor toegang tot diepe en smalle gebieden mogelijk is.

De 3/8" drive inbussleutsset is netjes opgeborgen in een geblazen doos, waardoor de inbusbits georganiseerd en gemakkelijk toegankelijk blijven.

Inhoud van de verpakking:

9 x SAE-inbusaansluiting: 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 3/8", 7/16"

【11 x metrische inbusbus】3 mm, 4 mm, 4,5 mm, 5 mm, 5,5 mm, 6 mm, 7 mm, 8 mm, 9 mm, 10 mm, 12 mm.

【1 x Blow Molded Box】


Steve
9 augustus 2025
Great. Helped reach otherwise inaccessible bolts. Storage container helps keep each item organized by size.
Vince DEBS
19 juni 2025
impeccable, très bonne qualité
ALBERTO V.
3 juni 2025
Muy bien presentadas, embalaje perfecto.
Service Engineer
18 mei 2025
PRODUCT:“LIBRATON 3/8" Drive Long Impact Hex Bit Socket Set, Allen Bit Sockets, S2 Steel Hex Head Sockets, 20PCS Allen Wrench Socket, SAE&Metric Allen Bit Socket Set, 6" Long Allen Key Sockets, Blow Molded Box By LIBRATON”------------20 piece 3/8” socket-Drive Allen hex wrench bits (6” long) set includes:11 Metric sizes: (3mm to 12mm): H3, H4, H4.5, H5, H5.5, H6, H7, H8, H9, H10, H129 SAE sizes: (1/8-inch to 7/16-inch): 1/8, 5/32, 3/16, 7/32, 9/32, 1/4, 5/16, 3/8, 7/16NOTE: 1/2” isn’t included, BUT the H12mm(11.97mm) = 0.471” so may be close enough?The shaft length is ~4.9” long, but total length with the 3/8” socket head is 5.9” long.------------------------LIKES:Have you ever had screws to insert or remove where they are “tight” the whole length, and cannot be simply spun out with your fingers? With Hex head screws the typical wrench is L shaped, or a longer T-Handle shape. Some short hex allen screw head sockets are available, but may not work where I’d need to use a long T-handle type wrench.THIS set is fantastic for that use case. I can use a ratchet wrench, impact driver, or drill to remove those screws with thread-lock on them easily.These are also great if you suffer from repetitive stress injury(RSI) in hands, or Carpal Tunnel, etc.Shaft sizes are: 1/4” for smaller sizes, then up to 8mm, then 10mm, then 12mm, & 5/16”, 7/16”For 6 of them, the Hex tip matches the size of the shaft.The other 14 have tips smaller than the shafts. (see pictures)The reduced tip size length is about 0.4” long, but the machined hex length may be shorter.Some smaller ones have machined hex lengths of ~0.25” long and 0.2” long for 1/8” and H3 sizes.I suspect that is to keep them as strong as possible since they are impact rated?The main time I can think of where that could be an issue is for some “SET SCREWs” where an allen head screw is recessed deeper, and the access hole is the same size as the screw.I include 2 pictures showing all the tips so you can decide for yourself if you have any “use cases” where that might be an issue, to “be prepared”.---------------Ever since I got a “complete” set of (cheap) L shaped allen wrenches years ago, only to find out that many of the smaller ones were machined TOO SMALL which then stripped out the screw heads when used -- I’ve been checking the smaller sizes to be sure they are NOT undersized:I measured the smaller ones in this set. I’m very pleased to find they will fit, and will NOT be too loose:1/8”(.125)= 0.1235”; 5/32(.1562)”= 0.155”; 3/16”(.1875) = 0.18553mm= 2.97mm; 4mm=3.96mm; 4.5mm=4.45mm---------------These bits are built very strong for impact driver use where that is possible or advisable.--------------------------------THE STORAGE CASE:The very Sturdy CASE has real hinges and a metal hinge pin (not a plastic flap). It also has a METAL closure latch which latches onto a wide/thick plastic tab.SAE sizes are on top BLUE colored half, and Metric are on the bottom BLACK half.Each slot has the size marked in raised lettering in plastic, as well as etched on the bit (so the size on the bit doesn’t have to be facing up to see its size in the box).Packed somewhat tightly for smaller storage size and better than others I’ve noted, but they are still finger accessible. (They are held in snugly and do NOT fall out when the case of folded over to close it!)When re-inserting a bit in the box, it inserts MUCH easier to have the parallel flat sides enter, with a corner facing up as you push down on the bit.Measured Plastic Case size: L~27cm(10.6”), W~19.7cm (7.75”), Depth 6.7cm (2.6“)The case OPENs to: 15” (38cm) x 10-5/8” (27cm)I see four molded feet on the bottom, (which also keep the metal latch clasp from rubbing on a surface).I also note identical but recessed feet size moldings on the TOP of the case for another case to stack into.This tells me that “Libraton” must also make other cases this same size with other tools in them.There is a tab with a 4mm(If several of these cases were stacked, a thin rod could be threaded through that hole of all of them and locked somehow?I do note that the case does NOT indicate what the contents are, so that’s a plus security wise.But not when looking for the right tool, so that’s what labels are made for.DISLIKE:A Quibble: It has 3 feet at the hinge side so that it stands mostly vertically.But if you try to stand it on either end or the front it will tilt, and more easily tip over.Probably my biggest annoyance is found when this is crammed into a transportable toolbox next to many other things. There is NO HANDLE to lift it out with!(I could try to open the latch and use that to lift it out with?- No, that side of the latch is not made for that.)BUT the nice thing about molded cases is that they are very easily modified. A simple slot through the plastic at either end of the catch side with a tie-wrap threaded through to grab onto works nicely. (or a string/rope if you prefer, only needing one drill hole at either latch-side end.)So: There’s not much NOT to like about this set.
lotito patrick
18 oktober 2024
outil bien presenter ,tres pratique