Nieuwe Elektrische Conversie Kit 24V36V250W voor Aangepaste Sleutel Gewone Fiets Road voor Elektrische Gear Fiets Derailleur

Non mi aspettavo un prodotto così bello... è arrivato in un imballaggio perfetto, devo dire che non è facilissimo montarlo ma neanche impossibile!!! Purtroppo la placca in ferro dove bisogna attaccarci il motore non era perfetta sul mio telaio infatti ho dovuto fare un aggiunta (come si può vedere nella foto)Attrezzi usati:Chiavi inglesi di varie misureCacciavitiPinzaE anche un pò di pazienza😂Conclusioni:Il motore si comporta molto bene ed è anche abbastanza potente, consiglio di confrontarsi con uno specialista nel campo delle batterie per farsi consigliare la batteria che si adatta meglio a questo motore.

Para una bici eléctrica

The kit shipped to me in the next day! I had been waiting for my order of battery which took a month! After connected every thing with my old bike, it worked enough with my expectation although it's not too fast in the fact that it's only 250W.

I put this on a 2018 Husky Girls bike. I powered it with two Neptune 12v 7ah batteries. I replaced the included 24v controller with a 24v 500watt one. Started out with a 20amp fuse inline, this blew first ride. Replaced with 30amp, fired it up, and it flies. Decent length ride, with the small batteries, but upped to 12ah after I saw what it does. I'm not sure what the actual motor rating is, but the motor doesn't get hot, with over a 20amp draw on it. This was the easiest build yet. I've built two trikes, but this was much easier. I didn't use the included chain, since I had some left over 410H chain, I used that. I don't like how the regular 410 chain stretches so I only use the heavy duty chain. On the build, I omitted the outside rubber spoke plate, and removed the dust cover, behind the brake arm. Mounted the center hole of the large sprocket with perfect fit over the spoke ring. It fits with enough clearance of the spokes, and will line up with the motor sprocket, with a little bending of the mounting plate. Be sure to add in a O-ring where you take out the dust cover, or your rear bearings will pickup sand quick. I plan on putting this kit bike, through some hard rides, and I'll follow up if I get any problems. I've got a little over 35 miles on the ride, so far, and haven't done anything, but charge the batteries.Update September 16 Still working great. No problem with motor at all. This is picture of how I worked it out on the Husky bike.Did cut the ends off of the bracket, to make plate fit flush with frame.Update: June 25,2020 Here it is in June, motor still runs great. Have modified the 24v to 36v, now. Added a 500w 36v controller, did this only to see if motor can handle the bigger controller. Still works great for me, only draw back was that the rear tire didn’t last long, before tread was nearly gone. No not from spinning out as you might assume, it will spin in sand but you can do that with pedal power if you’ve got the legs. I imagine the added push, plus lots of riding did the tire in, but if I had just rotated the front and back tires, when I first noticed it, would still be riding original. Motor has no noticeable heat, after full ride on my regular 6 mile run. Batteries don’t completely run down on trip, but are lower voltage at end, than original 24v batteries were. As an FYI, I am going back to the 24v as started, because three batteries are harder to balance on bike. I’ve heard of some having trouble with the sprocket failing. I haven’t had that problem, but I can see how it could happen. Wiggle the sprocket side to side, if you feel any sidewise slack, take the nut off, remove the sprocket, and look at backside. You will see a retainer ring with two little dents on it. Use whatever you can make fit both holes, and turn the ring clockwise in. This cover can get loose and unscrew, and drop the metal balls out, ruining the freewheel. That center silver looking piece, that is held with the nut, also will unscrew from the actual freewheel, and you can replace the freewheel using this aluminum bushing. L-faster sells a replacement complete freewheel that will fit this motor, here on Amazon. Happy biking.Update 01/11/2021Here it is January 2021, and still riding. Motor is still working great. Don’t have actual riding miles, I’ve put on it, but on third rear tire. As an FYI, get some good Silicone spray lube, and everytime you take care of cleaning and oiling your chain, spray the backside of the freewheel sprocket on the motor good too. Inside the sprocket, there are metal balls, and if they get dirty or rusty, they can make the back plate unscrew and drop the balls out. You can use the plastic straw looking part on the spray to aim the spray beside center. Spray in good, rotate the sprocket and repeat. If you see dirty looking liquid coming out, do it again. Little bit of house keeping on that and your chain, will make em last long time. I have electrified three bikes, and three trikes, since I started and they are all still going. No I only ride one, but the others are still going, with ages 12 to 74 doing the pedaling. I have to tell you though, for me it’s just as fun to build from scratch as it is to ride. This kit is far better than I had originally thought it would be. You may have to do a little thinking to figure out best way to mount the motor, but everything you need is there. Keep the chain tight, and all the bolts too, and you will get a lot of rides, you will enjoy. Happy pedaling.

Ürün iyi