Suptek Single Monitor Arm, Enkele Monitorarm (80cm in Hoogte Verstelbaar) voor 13-27 inch LCD LED Schermen, VESA 75/100mm tot 10kg, Tilt 90 ° Draaien 360 °, Monitorbeugel Monitorarm Beugel - MD6821

Good instructions included and also 2 ways of mounting the arm by drilling or just clamping the base.By drilling i was able to fit my 49inch! widescreen without too much bending because of the weight, clamping did bend the arm/pole a bit, so that's why i had to drill a hole in the desk and use this method that was also included in the box.Had to try it out since i needed the height and it worked out great.

Is een bouwpakket maar is makkelijk te doen, alle inbussleutels die je nodig hebt zitten er bij. Het scherm kan tot 80 cm in hoogte stellen. Er zijn 2 manieren om de arm te monteren aan de tafel of bureau en dit kan tot een dikte tot zo’n 10cm.

Like the title. The design is not half bad. Good mounting to desk etcetera.Problem is.It says it's rated for up to 10kg. But my 7kg monitor already gets this heavy and somewhat concerning sag in the joints.I'd say 7.5kg would be the absolute max with 6kg being the ideal maximum weight for this product.The sag in the points causes it to be alot more difficult to align

Apres autant d'utilisation je le recommande a 200% car toujours en place et je bouge souvent mon écran.

Holds up my 27 inch curved msi monitor with no problem at all, feels nice and sturdy and no worries that it will drop off. Easy to set up and install, takes about 5 mins and easy to adjust the height. It looks good as well and even has a little bit for hiding some of the cables round the back. Overall, a great product if you’re looking for a monitor stand

EDIT #2 ya compré un 2ndo! Agregue fotos ya de los 2 brazos(editado para agregar más). Es mi primer brazo para monitor. Si me tardé en armarlo ya qu vienen para poder poner de 2 maneras diferentes, me puse a leer los instructivos a detalle y claro como iba sostener un monitor que acabo de comprar. Quería que estuviera bien instalado.Quería este brazo ALTO ya que iba poner un monitor de 22"en forma vertical (para leer documentos) [ver imagen].Por ende tenía que tener mucha distancia (espacio) entre el escritorio y el monitor (o en mi caso más espacio entre el piso y el monitor). Para poder tener una trayectoria de la vista en un movimiento normal y no torcer hacia abajo (inclinación) para leer el documento.Este brazo mide 80cm de alto, si hubiera comprado uno normal de 40cm, me hubiera quedado muy abajo el monitor por lo mismo que tendría que forzar la vista hacia abajo cada vez que tenia que voltear al monitor.

It has worked well for me, at first for a small 18" touch monitor and now a 23". I can't speak for bigger monitors except to say this mount is solid and will definitely support more weight!I installed it by drilling a hole in my desk, be ready to take this step if the back edge of your computer is not that accessible. If it's within a couple inches of a wall, you won't be able to use the regular desk edge clamp mount, and you'll have to use the other mount that requires drilling a hole.Be sure that where you want to drill that hole is accessible on your desk too!Overall it's very solid in place, there's a tiny bit of play in the monitor, it's not 100% solid, but no mount like this will be. I still found it solid enough to use a touch screen on it, "your mileage may vary" on that.Don't know what else to say, it's overkill for small monitors but very solid and I went through about three of these before I settled on this one. It's serving me well on a 4 monitor setup putting a second monitor above my main monitor.

The product itself is great, little tough to get the arm in the pole but that’s minor and shows how strong the material is. The only issue was the instructions were vague and it came with a different kind of screw which weren’t in the instructions at all. However if you have dealt with assembling any sort of furniture you will find it easy to assemble with the pictures in the instructions.